Chronoport 2.0 Software
Chronoport 2.0 Software for Chronoskop CHR-8 Timegraphers v8.2 and higher
Witam na stronie Chronokomparatorów Prelis/Lisit
Hello and welcome to Chronoskop.com, the producer of electronic timegraphers!
I look forward to your visit and present to you our company profile. As timegrapher manufacturer we deal since 2006 with the design, manufacture and marketing of chronoscope timegraphers. Our highest priority is the highest quality of our products and the satisfaction of our customers. By the application of the latest SMD technology we always strive for the highest edge of technology. For the best possible adaptation to the customer requirements, we always remain open for questions and suggestions.
Furthermore, we are concerned with the development of inteligenten IT solutions for industry supported by many years of experience in the microcontroller electronics, CAD design and the broad field of programming.
For your satisfaction, we always give our best effort. I proudly even dare say that we have never left a customer dissatisfied. For the quality of our products and services I stand personally with my name.
CHRONOSKOP CHR-9 TIMEGRAPHER
CHR-9 – OUR NEW MODEL
Chronoscope CHR-9 is our new timegrapher model. CHR-9 is a fully electronic test instrument for measurement of mechanical watches that uses acoustic or optical signal of the clock. It can be determined values such as aisle, beat number, beat error and cycle time. For evaluation, the observation of the signals on the time axis or a diagrammatic representation of the passage may be used. All taken from the measurement information is displayed on the illuminated graphic display. With the headphone jack, you can listen to the operation of a clock directly. Thanks to a balance on the radio signal DCF77 with the atomic clock in Mainflingen an accuracy of up to a few seconds per year is achieved, which would otherwise only be realized with great technological effort. The use of the latest microcontroller technology in conjunction with modern SMD technology allows a compact solution that does not need to be ashamed in front of expensive large-scale equipment. Compact design (9cm x 9cm x 4cm) gives the device manageability; it is easy to transport and can be due to the external battery pack used as mobile device.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
Graphic dotmatrix touchdisplay with background lightning
2
Built in piezo microphone
3
External microphone socket
4
Microphone sensitivity control
5
3 LEDs for status display
6
Display contrast setting
7
Headphone output
8
Built in touch pen with shutdown function
9
Optical light barriers for measuring pendulum clocks
10
USB interface
11
Seriall interface (selected devices)
12
Input for calibration with the Mainflingen atomic clock with optional DCF 77 reciver
13
9-12 V supply voltage socket
14
9V battery case
15
Aluminium case
ACOUSTIC MEASUREMENT
The device is equipped with a built-in piezo microphone that allows an acoustic measurement of watches. For decoupling of the disturbances, the piezoelectric disc is supported on a foam. The device filters the noise digital. Due to the high sensitivity surrounding noise should still be avoided. A knob lets you adjust the sensitivity of the piezoelectric microphone.
OPTIC LIGHT BARRIER MEASUREMENT
The CHR 9 timegrapher allows a measurement of pendulum clocks based on the principle of optical light barrier. The corresponding IR transmitting diode and the receiving diode are incorporated in the rear wall of the device. In the optical measurement, a light beam is emitted from the infrared diode, and is received back after reflecting on a pendulum or the supplied reflector to a receiver diode in the device. As soon as during the measurement of a pendulum the pendulum interrupts the light beam, a pulse is detected. The reflector is included.
USB / SERIAL PORT + PC SOFTWARE
USB and Serial port + PC software CHRONO PORT 2.0 on CD
With the new PC software “CHRONO PORT 2.0” you can follow, print and save the measurement directly on the PC. All data are constantly sent to the computer and displayed as numerical values and graphics. Direct data transmission makes the entire measurement represented in a movable endless graphics window. The recognition of the ports happens automatically. Once the device is connected, the connection appears as “Connected”. The language of the software (English, German and Polish) can always be changed in the menu. Measurements can be saved as graphic a project and recalled later. The report of the measurement is summarized on a sheet of A4 paper. The software can be installed on the computer (2 MB), but can also start from the disc.
System requirements: MS Windows since version Windows 98th
The device also works without a PC.
RADIO WAVES CALIBRATION
Due to an adjustment by the radio signal DCF77 with the atomic clock in Mainflingen an accuracy of up to a few seconds per year can be achieved. The use of the latest microcontroller technology in connection with modern SMD technology allow a compact solution that does not need to be ashamed of expensive large-scale equipment. Compact design (9cm x 10cm x 4cm) gives the device manageability; it is easy to transport and can be used in many places due to the battery.
QUARTZ OVEN
Built quartz oven: The frequency of the clocking oscillator of the device may vary slightly depending on the ambient room temperature. This is not very important when the measurement takes place in unchanged room temperature, but in order to ensure maximum accuracy, the internal oscillator is heated controlled at a constant temperature. This compensates for the temperature dependence of the crystal. Thus, measurement of highest requirements.
OPTIONAL ACCESSORIES
DCF77 RADIO RECEIVER
Calibrating the internal quartz works via the comparison with the atomic clock in Mainflingen near Frankfurt. The time signal is broadcast over the radio signal. DCF77 is a longwave emitted over time signal. DCF77 is broadcast on the normal frequency of 77.5 kHz as time information in coded form. It has a range of about 2000 km around Frankfurt / Main or Mainflingen. In DCF77 signal the time information the next minute is coded. The DCF77 signal is the definition of the “right time” of Germany. The instrument is supplied calibrated. Once the measurements in comparable temperatures take place (for example, at the same room temperature), a new calibration is not necessary. ATTENTION! The reception of the signal is dependent on location and is outside Germany not guaranteed! The DCF77 receiver is not inevitably included and may have to be ordered.
POSITION MICROPHONE
With our location in microphone, you have the ability to measure a watch in any location. The clock is fixed with four sliders which are each fixed with a knurled screws. The position microphone is equipped with tripod thread to be mounted on a tripod (tripod is not included). Also, be aware to chose a tripod that holds the weight of the microphone and the clock. Our company is not liable for damages caused by falls of the microphone. Visible in the photo clock and is not part of the position microphone.
CROCODILE MICROPHONE
The crocodile microphone is to be clipped to the watch case. Especially suitable for measuring mechanisms of large clocks. Very good decoupling from the ambient noise.
EXTERNAL LIGHT BARIER
Light barrier sensor is under construction
HISTORY OF CHRONOSKOP TIMEGRAPHERS
We assumed the activity in 2006 as PRELIS Electronic in Germany. Initially, the company was engaged in design, production and sale of timegraphers – electronic devices used to measure the accuracy of mechanical clocks (see: Chronoskop). Soon our activity extended on application of intelligent electronic solutions based on microcontroller electronic.
After moving the business to the Poland in 2015 as a consequence of merger with ML-IT company we transformed into the current form – Lisit.net. At the same time our range of services expanded for broad services in the IT industry.
All timegraphers are soldered and assembled by hand in Germany and in Poland.
Chronoskop CHR-8
Chronoskop CHR-7
Chronoskop CHR-6
Chronoskop CHR-5
SUPPORT
SOFTWARE DOWNLOADS
Switching from the Chronoport 1.0 to Chronoport 2.0, an upgrade of the hardware is necessary, which must be made by us.
USER MANUALS
FAQ
DO I NEED TO DCF77 RECEIVERS?
Each appliance that leaves our house is calibrated prior to shipping. Recalibration is not necessary for measurements. Would still perform a new calibration, however, please order the optional DCF77 receiver.
CAN MICROPHONES THIRD PARTY BE CONNECTED?
When using the appropriate adapter to 3.5mm jack, it is possible to use piezoelectric microphones from other manufacturers, as they are not operated or reinforced with its own power supply. Due to large range of third-party, we can not offer an adapter for connection.
HOW LONG CAN THE MAXIMUM LENGTH MEASUREMENT / INTEGRATION TIME BE?
Our Geraet recorded maximum 65,000 strokes in the measurement. The maximum measurement time (and hence also the integration time) shall be determined from the stroke rate. In a Schagzahl of 18000, the maximum integration time is thus 65000/1800 = 36,1h. With deactivated integration to measure only the last 5 seconds are considered.
WHY DO I SOMETIMES DIFFERENT RESULTS IN TWO SUCCESSIVE FOLLOWING MEASUREMENTS?
As a result of the measurement is, when switched integration time, the current measured value, or with activated time integration, the measured value, which is averaged over the total duration of the measurement. Note, however, that the transition of a clock, for example, in the first minute is different from the next. If the measurement result is near an ideal clock, it can even mean different signs of the measurement result. This behavior can be observed on the graphical representation of measuring well. In these cases, a longer measurement is needed which provides a stable average value is necessary.
CAN VALUES AS PRESSURE, ENVIRONMENTAL TEMPERATURE AND HUMIDITY IN THE MEASUREMENT BE INVOLVED?
No. A development in this regard is, however, contemplated.
HOW TO ORDER A TIMEGRAPHER
ORDER NOW
DELIVERY
- The timegrapher
- headphones
- Power Supply
- Reflector for photoelectric measurement
- Serieles PC connection cable
- software CD
- User manual in English and German
- Packing with foam inserts
SATISFACTION GUARANTEE
Buy without risk! Test the device and let yourself be convinced of its sophisticated technology and best design! Failure Gefalen you have 14 days to return without giving any reason! That satisfaction is our biggest priority is our 100% positive feedback rating!
SHIPPING
Germany.
Standard delivery time: 1 to 2 days. 5.00 EUR
Belgium, Denmark, Luxembourg, Netherlands, Austria.
Standard delivery time: 1 to 2 days. 12.50 EUR
France, Great Britain, Italy, Poland, Sweden, Slovakia, Slovenia, Czech Republic, Hungary.
Standard delivery time: 2 to 3 days. 15.50 EUR
Estonia, Finland, Ireland, Latvia, Lithuania, Portugal, Spain.
Delivery time: 3 to 4 days. 20.50 EUR
When Also order of optional accessories are no Adicional shipping.
The shipment is insured. It will be charged no more and no less than the actual shipping costs. Shipping costs for other countries ask from the table below the description found. It will be shipped only within the EU. This also applies to any subsequent Garantiefaelle. When Also order of optional accessories are no Adicional shipping.